Can-Am Maverick X3 Vented Full Windshield, 1/4" Polycarbonate, 3-Position Vents

A full windshield keeps dust, bugs and cold air off you, but a sealed-up cab can get stuffy fast once the sun comes out. This vented full windshield for the Can-Am Maverick X3 solves both problems: tough 1/4" polycarbonate up front, and three-position vents you can open or close by hand from the seat. You get steady protection on cold mornings and fresh air when the afternoon heats up, all without fussing with hinges or latches.

Highlights

• Three-position BreezeRite vents let you control airflow
• Vehicle-specific fit makes installation easy and secure
• 1/4" polycarbonate is 250x stronger than glass
• XR Optic hard coating resists scratches and UV damage
• 1-year warranty from the manufacturer
• Made in the USA

Total Control of Your Cab's Airflow

The injection-molded BreezeRite vents have three settings: fully closed, half open, and fully open. They're sturdy enough to stay exactly where you set them, even on rough ground, and you can reach up and adjust them by hand without stopping. Shut them and the cab stays warm and toasty. Open them and you get waves of cool, fresh air across the cab. It's a level of comfort control you don't get from a plain sheet of polycarbonate.

1/4" Polycarbonate Strength

This windshield is cut from 1/4" polycarbonate, the go-to material for UTV windshields because nothing else handles impacts as well. Polycarbonate is 25 times stronger than acrylic and 250 times stronger than glass. Rocks, branches and other big trail debris that would crack lesser windshields just bounce off, so you can ride hard knowing the windshield can take the hits.

XR Optic Hard Coating on Both Sides

Bare polycarbonate scratches easily, which is why this windshield gets the XR Optic hard coating on both faces. The coating makes the surface scratch resistant, so a low-hanging branch or a quick wipe doesn't leave a haze of fine scratches. It's also UV resistant, so the windshield won't turn yellow or fade no matter how many hours it spends in the sun. Strong polycarbonate plus this proprietary coating is why these windshields hold up to hard use.

Experienced Windshield Builders

The manufacturer behind this windshield has built and shipped hundreds of thousands of UTV windshields to riders around the world, and every one is made in the USA. That experience shows in the fit: it follows the contours of the X3's cage and hood, it's built to be rattle free, and the vents open and close easily. A little care goes a long way too; clean it with products made for polycarbonate to keep it clear for years.

Flip vs. Vented Full Windshields

Flip windshields

• Give full protection when closed, but open up for an open-cab feel
• Great for changing weather; switch from trail to trailer mode in seconds
• Slightly heavier, with more moving parts to maintain

Vented full windshields (this one)

• Always-on protection with adjustable airflow through built-in vents
• Less complex than flip designs, with fewer hinges and latches
• Compatible with wipers and washers, and stable at higher speeds
• Doesn't offer as much maximum airflow as a flip windshield

Quick takeaway: choose a flip windshield for maximum versatility across conditions. Choose a vented full windshield for steady protection with simple, reliable airflow control.

Features and Specs

• Protects against debris and the elements
• Made of 1/4" polycarbonate, 250x stronger than glass and 25x stronger than acrylic
• Injection-molded BreezeRite vents with three vent positions
• Proprietary XR Optic hard coating for scratch resistance
• Fits the contours of your cage and hood
• Comes complete with all hardware for easy installation
• Made in the USA

Care Tips

To keep the hard coating doing its job, rinse off grit with plenty of water before you wipe the windshield, and use a soft microfiber towel with a cleaner that is safe for polycarbonate. Skip ammonia-based glass cleaners and paper towels, which can dull the surface over time.

Choosing Your Version

When you order, pick whether your X3 has a factory intrusion bar. The two versions are built to clear each setup, and each has its own install sheet below. The windshield can be used with either a hard or soft top.

Who It's For and What Pairs Well

This windshield fits riders who want year-round protection with the option to let air in, from cold-weather trail riders to dusty desert runners. Close in the rest of the cab with a top from Can-Am Maverick X3 roof tops, and compare other styles in X3 windshields.

Fitment

64” Models

72” Models

Note: Can be used with hard or soft tops

Installation

All mounting hardware is included and the windshield is shaped to the X3 cage, so installation is straightforward. Use the instruction sheet that matches your intrusion bar setup.

• Installation instructions (WS-CA-X3-70, PDF)
• Installation instructions (WS-CA-X3-RC, PDF)