The RZR Pro XP is a desert-bred sport machine, but it is also a lot of horsepower to put to work in the snow. This Denali kit pairs the MA11741 Pro XP mount plate with Denali pushtubes and the blade you choose, so your Pro XP can clear the driveway before it hits the trail. The mount stays put, and the plow comes off with a pin pull.
Why It Works on a Pro XP
- The MA11741 mount plate is designed for the 2020-2026 RZR Pro XP frame and built from laser-cut 1/4 in. steel.
- Welded construction stands up to impacts and lets the mount stay on for general riding.
- PRO curved blades in red, black or yellow can match your Pro XP's colors.
- Ten angle positions handle straight pushes or windrowing to one side.
- Replaceable 7-gauge wear bar protects the blade edge on gravel.
Choosing Your Blade
- Straight HD blade (60, 66 or 72 in., black): one-piece 11-gauge steel face with a 19 in. scoop. Kit adds $0 / $50 / $100 as you go wider.
- PRO curved blade (66 or 72 in., black, red or yellow): one-piece 12-gauge steel with tapered ends that throw snow off to the side like a DOT truck plow. PRO kits add a rubber snow flap and plow marker flags.
- Rule of thumb: pick a blade at least as wide as your machine is track-to-track, so you are not driving over the edge of every pass.
Plowing Tips for Pro XP Owners
- Take it easy on the throttle; the Pro XP has more power than a plow needs, and smooth inputs keep the tires hooked.
- Angle the blade to windrow on long drives, then square it up to push the pile clear.
- Check winch rope routing before every storm so the rope lifts the blade straight.
Denali Plow Specifications
- Blade scoop: 19 in. with a 65-degree attack angle and over-center design so snow rolls up and is thrown forward
- Four full-height 7-gauge ribs plus three 7-gauge horizontal stabilizers at the deepest point of the blade
- Replaceable 7-gauge steel wear bar and height/angle adjustable skid feet
- Pushtubes: impact-resistant reinforced pivot with two extra support bars and a structural tube steel cross bar
- Manual angle: 0, 12.5 or 25 degrees left or right; 13.5 in. center-to-center plow mount tabs
- Mount plate: laser-cut 1/4 in. steel, fully welded, with slotted holes that let the blade follow the ground
- Winch required to raise and lower the blade (not included)
Fitment
| Year | Make | Model |
|---|---|---|
| 2020-2026 | Polaris | RZR Pro XP |
Note: Moto Alliance lists this mount for the RZR Pro XP. Pro XP 4 fitment is not stated on the mount listing.
What's in the Box
- Denali mount plate MA11741 with mounting hardware
- Denali UTV pushtubes with quick-release pins (pins included)
- Your choice of Denali blade
- 7-gauge steel wear bar
- Adjustable skid feet
- PRO curved blade kits only: rubber snow flap and plow marker flags
- Installation hardware and instructions
Who It's For and What Pairs Well
This kit is for Pro XP owners who ride all winter and want one machine for snow duty too. Lift it with a Viper winch from RZR Pro XP recovery gear, and add a Pro XP windshield and Firestorm heater from Pro XP interior accessories.
Installation Notes
Install the MA11741 mount with the included hardware following the PDF. A winch is required and must be installed before the plow will lift. Set skid-foot height after mounting the blade, with the car on level ground.
- source:
- motoalliance
- ma_url:
- https://www.motoalliance.com/utv-snow-plow-mount-plate-rzr-pro-xp
- desc_status:
- written_2026-10-27
- ma_parts:
- MA11741 $149.99 + PTUT $300 + blade $320-$500 (BLST60UTV,BL66STBK,BL72STBK,BLPro66/72 BK/RE/YE)
