Honda Pioneer 1000 owners tend to be the kind of people who plow at 5 a.m. so the rest of the place can get moving. This Denali kit pairs the MA11719 Pioneer 1000 mount plate with Denali pushtubes and your choice of blade, giving you a complete plow from one listing. The steel mount stays on the Pioneer year-round, and the plow pins off in minutes.
What You Get on a Pioneer 1000
- Mount plate designed for the Pioneer 1000 frame and built from laser-cut 1/4 in. steel.
- Over-center blade design with a 65-degree attack angle that rolls snow forward instead of letting it pile over the top.
- Ten manual angle settings for windrowing or straight pushing.
- Steel wear bar and skid feet are both replaceable or adjustable for gravel versus concrete.
- Choose straight or PRO curved blades from 60 to 72 in.
Choosing Your Blade
- Straight HD blade (60, 66 or 72 in., black): one-piece 11-gauge steel face with a 19 in. scoop. Kit adds $0 / $50 / $100 as you go wider.
- PRO curved blade (66 or 72 in., black, red or yellow): one-piece 12-gauge steel with tapered ends that throw snow off to the side like a DOT truck plow. PRO kits add a rubber snow flap and plow marker flags.
- Rule of thumb: pick a blade at least as wide as your machine is track-to-track, so you are not driving over the edge of every pass.
Tips for Plowing with a Pioneer 1000
- Use four-wheel drive and low range when pushing heavy, wet snow.
- Windrow with the blade angled, then come back straight to push the pile back.
- Lower the blade fully before you start moving so the wear bar sets the plow height, not the winch rope.
Denali Plow Specifications
- Blade scoop: 19 in. with a 65-degree attack angle and over-center design so snow rolls up and is thrown forward
- Four full-height 7-gauge ribs plus three 7-gauge horizontal stabilizers at the deepest point of the blade
- Replaceable 7-gauge steel wear bar and height/angle adjustable skid feet
- Pushtubes: impact-resistant reinforced pivot with two extra support bars and a structural tube steel cross bar
- Manual angle: 0, 12.5 or 25 degrees left or right; 13.5 in. center-to-center plow mount tabs
- Mount plate: laser-cut 1/4 in. steel, fully welded, with slotted holes that let the blade follow the ground
- Winch required to raise and lower the blade (not included)
Fitment
| Year | Make | Model |
|---|---|---|
| 2016-2025 | Honda | Pioneer 1000 |
What's in the Box
- Denali mount plate MA11719 with mounting hardware
- Denali UTV pushtubes with quick-release pins (pins included)
- Your choice of Denali blade
- 7-gauge steel wear bar
- Adjustable skid feet
- PRO curved blade kits only: rubber snow flap and plow marker flags
- Installation hardware and instructions
Who It's For and What Pairs Well
This kit is for Pioneer 1000 owners clearing farm lanes, barnyards and driveways. Lift the blade with a winch from our Honda Pioneer winch and recovery section, and pair it with a Pioneer cab heater and Pioneer doors or cab enclosure.
Installation Notes
Follow the MA11719 PDF to bolt the mount to the Pioneer frame with the included hardware. A winch is required to raise and lower the blade. Check all mount bolts again after the first few hours of plowing.
- source:
- motoalliance
- ma_url:
- https://www.motoalliance.com/utv-snow-plow-mount-plate-pioneer-1000
- desc_status:
- written_2026-10-27
- ma_parts:
- MA11719 $149.99 + PTUT $300 + blade $320-$500 (BLST60UTV,BL66STBK,BL72STBK,BLPro66/72 BK/RE/YE)
