Universal 2" Receiver UTV Viper V3 Winch Kit - 4,500 or 6,000 lb with Receiver Mount & Fairlead Mount

Not every machine has a bolt-on winch plate, and some owners want one winch they can move from the front of the machine to the back. This kit is built around the Viper MA11970 2 in. receiver winch mount, which slides into any 2 in. hitch receiver, and adds the matching Viper fairlead mount and a Viper V3 winch. Choose the 4,500 lb standard spool or the 6,000 lb wide spool.

Why a Receiver Winch

• Multi-mount winch cradle lets you move the winch between front and rear receivers, per Moto Alliance.
• Holds up to a 6,000 lb ATV/UTV winch and accepts standard and wide 4-bolt patterns.
• Matching Viper universal fairlead mount included, sized to the winch you pick.
• Powder-coated black and shipped with its mounting hardware and instructions.
• One winch can serve more than one machine, as long as each has a 2 in. receiver and matching wiring.

4,500 or 6,000 lb?

• V3 4,500 standard spool: lighter and shorter, with 40 ft of rope. Plenty for self-recovery and lifting a Denali plow on most machines.
• V3 6,000 wide spool: adds $80, a wider drum and 60 ft of rope. A good pick for heavier machines, crew cabs with a loaded bed, or anyone who winches other people out.

Receiver Winch Tips

• A receiver winch pulls through the hitch, so use a quality receiver bolted to the frame and rated for the load.
• Use a snug hitch pin and clip; a loose pin lets the mount rattle and wear.
• Pull as straight as you can. Side loads on a receiver mount stress the hitch more than a bolted plate.
• Carry the wireless remote with the winch, since the mount may move between machines.

Viper V3 Winch Specifications

• Motor: 12V DC sealed permanent magnet
• Gear train: 3-stage planetary metal gears
• Brake: automatic, 100% load holding
• Clutch: sliding ring gear
• Wiring: 6 gauge; tie rods, fairlead hardware and motor terminals are stainless steel
• Sealing: IP67 waterproof rating per Moto Alliance; corrosion-resistant aluminum housing
• Wireless remote with its own frequency, plus a rocker handlebar switch and dash switch
• Manufacturer warranty: limited one year on the winch, 6 months on the rope
• V3 4,500 standard spool: 40 ft x 1/4 in. synthetic rope, 3.0 x 4.875 in. bolt pattern, 13.3 x 4.75 x 4.6 in., 17 lb
• V3 6,000 wide spool: 60 ft x 1/4 in. synthetic rope, 3.0 x 6.6 in. bolt pattern, 15 x 4.75 x 4.6 in., 18 lb

Fitment

Note: Moto Alliance says this mount needs a fairlead mounting bracket, so this kit includes the matching Viper universal fairlead mount: MA11001 (standard) with the 4,500 lb winch or MA11001W (wide) with the 6,000 lb winch.

Note: The receiver itself is not included. Moto Alliance notes extra wiring length may be needed, especially for a rear receiver; add the extended wiring pack above if you need it.

What's in the Box

• Viper MA11970 2 in. receiver winch mount with hardware and instructions
• Viper universal fairlead mount (MA11001 standard or MA11001W wide, matched to your winch)
• Viper V3 winch in your choice of rope color
• 40 ft or 60 ft x 1/4 in. synthetic rope, aluminum hawse fairlead and clevis hook
• Wireless remote, rocker switch, dash switch, contactor, wiring and hand saver strap

Who It's For and What Pairs Well

This kit is for owners of machines without a model-specific plate, and for anyone who wants to winch backward out of trouble or swap one winch between two rigs. Browse universal UTV recovery gear and winches and the UTV overland recovery gear section for straps, shackles and snatch blocks.

Installation Notes

Assemble the winch and fairlead mount on the MA11970 cradle using the PDF below, then slide it into the receiver and pin it. For a permanent setup, run the power leads to the battery and add a quick-connect plug at each receiver you plan to use. Moto Alliance notes extra wiring length may be needed, so measure before you buy cable.

• Moto Alliance MA11970 winch mount installation instructions (PDF)