Can-Am Maverick X3 Denali Snow Plow Kit - 60-72 Inch Blade, Pushtubes, Plow Mount & Winch Mount

A Maverick X3 is not the first machine people think of for plowing, but plenty of owners in snow country want one machine that does it all. This Denali kit makes it work, pairing the MA11749 X3 plow mount (with the MA11949 winch mount it needs) with Denali pushtubes and the blade you choose. Ride all summer, then pin the plow on when the snow flies.

Built Around the X3 Chassis

• The X3 plow mount ties into the Viper winch mount for a solid connection point on a sport chassis.
• Laser-cut 1/4 in. steel with welded side walls; can stay on the car for general riding.
• Choose a 60 or 66 in. blade for trails and paths, or 72 in. for wider driveways.
• PRO curved blades in black, red or yellow can match your X3 color.
• Centered mount spreads impact loads through the frame instead of the front suspension.

Choosing Your Blade

• Straight HD blade (60, 66 or 72 in., black): one-piece 11-gauge steel face with a 19 in. scoop. Kit adds $0 / $50 / $100 as you go wider.
• PRO curved blade (66 or 72 in., black, red or yellow): one-piece 12-gauge steel with tapered ends that throw snow off to the side like a DOT truck plow. PRO kits add a rubber snow flap and plow marker flags.
• Rule of thumb: pick a blade at least as wide as your machine is track-to-track, so you are not driving over the edge of every pass.

Winter Setup Tips for the X3

• Because the X3 sits lower than a utility machine, set the skid feet first so the blade does not lift the front end on hard pack.
• Use the straight angle for deep, wet snow and angle the blade for light, fluffy snow you want thrown to the side.
• Plow before the snow gets packed by traffic; the X3 has the power, but traction is the limit.

Denali Plow Specifications

• Blade scoop: 19 in. with a 65-degree attack angle and over-center design so snow rolls up and is thrown forward
• Four full-height 7-gauge ribs plus three 7-gauge horizontal stabilizers at the deepest point of the blade
• Replaceable 7-gauge steel wear bar and height/angle adjustable skid feet
• Pushtubes: impact-resistant reinforced pivot with two extra support bars and a structural tube steel cross bar
• Manual angle: 0, 12.5 or 25 degrees left or right; 13.5 in. center-to-center plow mount tabs
• Mount plate: laser-cut 1/4 in. steel, fully welded, with slotted holes that let the blade follow the ground
• Winch required to raise and lower the blade (not included)

Fitment

Note: On the X3, the plow mount uses the Viper MA11949 winch mount as a connection point. Moto Alliance lists MA11949 as included with this mount.

Note: The MA11949 winch mount's own listing shows 2017-2025 fitment, while this plow mount is listed through 2026. If you own a 2026 X3, check with us before ordering.

What's in the Box

• Denali mount plate MA11749 with mounting hardware
• Viper MA11949 winch mount (required connection point; listed by Moto Alliance as included)
• Denali UTV pushtubes with quick-release pins (pins included)
• Your choice of Denali blade
• 7-gauge steel wear bar
• Adjustable skid feet
• PRO curved blade kits only: rubber snow flap and plow marker flags
• Installation hardware and instructions

Who It's For and What Pairs Well

This kit is for X3 owners in snow country who would rather not buy a second machine just to clear a driveway. Pick a winch from our Maverick X3 recovery gear section, and add a Maverick X3 windshield so you are not wearing every pass.

Installation Notes

Install the MA11949 winch mount first, then the MA11749 plow mount, using the hardware and steps in the PDF. A winch on the MA11949 mount is required to lift the blade. Before the first storm, run the blade up and down a few times to check winch rope routing.

• Moto Alliance MA11749 mount installation instructions (PDF)