Honda Talon Denali Snow Plow Kit - 60-72 Inch Blade, Standard or Extended Pushtubes & Mount Plate

The Honda Talon is a long-travel sport machine, and its suspension geometry is why this kit gives you a choice of pushtubes. You get the Denali MA11720 Talon mount plate, a Denali blade in your size and either standard pushtubes or 15 in. extended pushtubes, which Moto Alliance recommends for the Talon 1000R. Everything ships as one complete plow.

Built for the Talon's Long-Travel Stance

• Separate pushtube choice: standard tubes, or extended tubes for the Talon 1000R per Moto Alliance.
• Talon-specific MA11720 mount plate in laser-cut 1/4 in. steel, welded for strength and left on year-round.
• Straight or PRO curved blades from 60 to 72 in.
• Ten angle positions and a quick pin release for easy on and off.
• Upgrading to extended pushtubes adds $110, the same as buying that part on its own.

Choosing Your Blade

• Straight HD blade (60, 66 or 72 in., black): one-piece 11-gauge steel face with a 19 in. scoop. Kit adds $0 / $50 / $100 as you go wider.
• PRO curved blade (66 or 72 in., black, red or yellow): one-piece 12-gauge steel with tapered ends that throw snow off to the side like a DOT truck plow. PRO kits add a rubber snow flap and plow marker flags.
• Rule of thumb: pick a blade at least as wide as your machine is track-to-track, so you are not driving over the edge of every pass.

Plowing Tips for Talon Owners

• Choose the extended pushtubes on a 1000R so the blade sits flat at the 1000R's ride height.
• With the long-travel suspension, push slowly so the front end does not dive into the snow.
• Raise the blade fully for transport and check the winch rope before each use.

Denali Plow Specifications

• Blade scoop: 19 in. with a 65-degree attack angle and over-center design so snow rolls up and is thrown forward
• Four full-height 7-gauge ribs plus three 7-gauge horizontal stabilizers at the deepest point of the blade
• Replaceable 7-gauge steel wear bar and height/angle adjustable skid feet
• Pushtubes: impact-resistant reinforced pivot with two extra support bars and a structural tube steel cross bar
• Manual angle: 0, 12.5 or 25 degrees left or right; 13.5 in. center-to-center plow mount tabs
• Mount plate: laser-cut 1/4 in. steel, fully welded, with slotted holes that let the blade follow the ground
• Winch required to raise and lower the blade (not included)

Fitment

Note: Moto Alliance recommends the extended pushtubes for Honda Talon 1000R models. Choose "Extended Pushtubes" in the options above for a 1000R.

Note: Extended pushtubes are 15 in. longer than standard, and Moto Alliance says they do not work with the Denali pushtube lift kits or the hydraulic angle system.

What's in the Box

• Denali mount plate MA11720 with mounting hardware
• Denali UTV pushtubes with quick-release pins (pins included)
• Your choice of Denali blade
• 7-gauge steel wear bar
• Adjustable skid feet
• PRO curved blade kits only: rubber snow flap and plow marker flags
• Installation hardware and instructions

Who It's For and What Pairs Well

This kit is for Talon owners who keep riding through winter and want to clear their own driveway or trailhead. Lift the plow with a winch from Honda Talon recovery gear, and keep snow out of your face with a Talon windshield.

Installation Notes

Install the MA11720 mount following the PDF with the included hardware. A winch is required for blade lift. On 1000R models, the extended pushtubes help the blade sit at the right height for the long-travel suspension. If you are not sure which Talon you have, send us the VIN or a photo of the front end and we will help you pick standard or extended tubes before it ships.

• Moto Alliance MA11720 mount installation instructions (PDF)