The General is the crossover machine of the Polaris lineup, and with a plow on the front it becomes a legit winter tool. This kit bundles the Denali MA11706T-GEN mount plate, Denali pushtubes and your blade of choice for every 2016-2027 General model. Once the mount is on, the blade attaches with pins and comes off just as fast.
Why General Owners Choose Denali
- Covers every General from 2016 through 2027 per Moto Alliance fitment, including the 1000 and XP trims.
- 1/4 in. laser-cut steel mount plate with welded side walls that will not twist when you hit a frozen windrow.
- Pick a lighter 60 in. straight blade for tight paths, or a 72 in. PRO curved blade for long driveways.
- Ten angle positions handle everything from straight pushes to windrowing snow off a sidewalk edge.
- Replaceable 7-gauge wear bar takes the scraping so the blade face lasts for seasons.
Choosing Your Blade
- Straight HD blade (60, 66 or 72 in., black): one-piece 11-gauge steel face with a 19 in. scoop. Kit adds $0 / $50 / $100 as you go wider.
- PRO curved blade (66 or 72 in., black, red or yellow): one-piece 12-gauge steel with tapered ends that throw snow off to the side like a DOT truck plow. PRO kits add a rubber snow flap and plow marker flags.
- Rule of thumb: pick a blade at least as wide as your machine is track-to-track, so you are not driving over the edge of every pass.
Plowing Tips for General Owners
- Start with the blade angled 25 degrees on the first pass down a driveway, then push the windrow off the edge on the way back.
- On gravel, raise the skid feet a notch so the wear bar rides on top of the stones instead of digging them into the yard.
- Keep a little tension on the winch rope when the blade is down; a slack rope can wrap the drum unevenly.
Denali Plow Specifications
- Blade scoop: 19 in. with a 65-degree attack angle and over-center design so snow rolls up and is thrown forward
- Four full-height 7-gauge ribs plus three 7-gauge horizontal stabilizers at the deepest point of the blade
- Replaceable 7-gauge steel wear bar and height/angle adjustable skid feet
- Pushtubes: impact-resistant reinforced pivot with two extra support bars and a structural tube steel cross bar
- Manual angle: 0, 12.5 or 25 degrees left or right; 13.5 in. center-to-center plow mount tabs
- Mount plate: laser-cut 1/4 in. steel, fully welded, with slotted holes that let the blade follow the ground
- Winch required to raise and lower the blade (not included)
Fitment
| Year | Make | Model |
|---|---|---|
| 2016-2027 | Polaris | General (all models) |
Note: Moto Alliance publishes a separate drilling guide for the General mount. Review it before install so you know what to expect.
What's in the Box
- Denali mount plate MA11706T-GEN with mounting hardware
- Denali UTV pushtubes with quick-release pins (pins included)
- Your choice of Denali blade
- 7-gauge steel wear bar
- Adjustable skid feet
- PRO curved blade kits only: rubber snow flap and plow marker flags
- Installation hardware and instructions
Who It's For and What Pairs Well
This kit is for General owners who want one machine that trail rides in summer and plows in winter. Lift the blade with a Polaris General winch kit, warm the cab with a General cab heater, and keep snow off you with a General windshield.
Installation Notes
Read through both PDFs below; the mount install uses the supplied hardware, and Moto Alliance includes a separate drilling guide for this General mount. A winch is required for blade lift. Set skid-foot height last, with the machine on level ground.
- source:
- motoalliance
- ma_url:
- https://www.motoalliance.com/denali-utv-snow-plow-mount-general
- desc_status:
- written_2026-10-27
- ma_parts:
- MA11706T-GEN $149.99 + PTUT $300 + blade $320-$500 (BLST60UTV,BL66STBK,BL72STBK,BLPro66/72 BK/RE/YE)
