Polaris Ranger 1000 / XP 1000 / SP 570 Denali Snow Plow Kit - 60-72 Inch Steel Blade, Pushtubes & Mount

A Ranger is already the hardest-working machine on most farms and acreages, and this kit lets it clear the driveway, the lane and the shop apron too. It pairs the Denali MA11752 frame mount with Denali pushtubes and your pick of blade in one order, so you are not piecing together part numbers in November. The mount stays on the Ranger all year, and the blade comes off in minutes when the snow is gone.

Why This Kit Works on a Ranger

• Frame-mounted, centered design sends the hit from a buried curb or frozen drift into the strongest part of the Ranger instead of the front A-arms or bumper.
• Built for the 2020-up full-size Ranger 1000 and XP 1000 with the factory brushguard, plus 2022-up Ranger SP 570 Northstar and Premium trims.
• A 72 in. blade covers the Ranger's full track width on each pass, which matters when you are pushing heavy, wet snow out of a long lane.
• Ten blade angle positions let you windrow snow to one side of a driveway or square it up for straight pushes in a yard.
• Slotted mount holes let the blade float and follow uneven gravel instead of riding up on the high spots.

Choosing Your Blade

• Straight HD blade (60, 66 or 72 in., black): one-piece 11-gauge steel face with a 19 in. scoop. Kit adds $0 / $50 / $100 as you go wider.
• PRO curved blade (66 or 72 in., black, red or yellow): one-piece 12-gauge steel with tapered ends that throw snow off to the side like a DOT truck plow. PRO kits add a rubber snow flap and plow marker flags.
• Rule of thumb: pick a blade at least as wide as your machine is track-to-track, so you are not driving over the edge of every pass.

Denali Plow Specifications

• Blade scoop: 19 in. with a 65-degree attack angle and over-center design so snow rolls up and is thrown forward
• Four full-height 7-gauge ribs plus three 7-gauge horizontal stabilizers at the deepest point of the blade
• Replaceable 7-gauge steel wear bar and height/angle adjustable skid feet
• Pushtubes: impact-resistant reinforced pivot with two extra support bars and a structural tube steel cross bar
• Manual angle: 0, 12.5 or 25 degrees left or right; 13.5 in. center-to-center plow mount tabs
• Mount plate: laser-cut 1/4 in. steel, fully welded, with slotted holes that let the blade follow the ground
• Winch required to raise and lower the blade (not included)

Fitment

Note: This mount is listed for Rangers that have the factory front brushguard. If your Ranger has an aftermarket bumper, check with us before ordering.

Note: Moto Alliance says the Denali pushtube lift kits and the 15 in. extended pushtubes do not work with this mount (MA11752).

What's in the Box

• Denali mount plate MA11752 with mounting hardware
• Denali UTV pushtubes with quick-release pins (pins included)
• Your choice of Denali blade
• 7-gauge steel wear bar
• Adjustable skid feet
• PRO curved blade kits only: rubber snow flap and plow marker flags
• Installation hardware and instructions

Who It's For and What Pairs Well

This kit is for Ranger owners who plow their own place or a few neighbors and want a steel blade that will not fold the first time it meets a frozen windrow. Lift and lower it with a Polaris Ranger winch kit, and close in the cab with a Ranger cab heater and roof so long plowing sessions are comfortable.

Installation Notes

The mount plate bolts to the Ranger frame with the supplied hardware; plan on an afternoon in the garage with basic hand tools. You need a working winch on the front of the Ranger before the plow can be raised. Set the skid feet so the wear bar just kisses the ground, then fine-tune after the first storm.

• Moto Alliance MA11752 mount installation instructions (PDF)